K88600 Portable octane analyzer,115V 60 HZK88690 Portable octane analyzer,220-24050/60 HZDetermines the Pump Octane Number (AKI), Research Octane Number (RON), and Motor Octane Number (MON) of unleaded gasoline, ethanol blended gasoline, leaded gasoline and Cetane Number for diesel fuels.Test results equivalent to ASTM D2699 and D2700 test methodsMeasures all grades of unleaded gasoline and ethanol blended gasolineTest results equivalent to ASTM D613 for Cetane Number of diesel fuels (Optional with K88612)Displays results in 20 secondsDirectly measures octane number for {(R+M)}/2, RON and MONOptional feature for cetane number determination of diesel fuelsIncludes RS-232 output, built-in printer and LCD displayResults traceable to official knock engine laboratoryGPS model available for use with GPS locator accessory Safety Features Out of Temperature Range Warning: Analyzer displays Out of Range Warning Message when instrument in being used outside of its standard operating temperature range. Either above 38°C or below 7°C.Out of Calibration Range Warning: Analyzer displays “Too High” or “TooLow” message when measurement reading is out of the instruments calibration range.Bad Curve Warning: Analyzer warns user when light protective lid is not on during testing. External light source will greatly disrupt resultsMeasures octane number via near-infrared (NIR) transmission spectroscopy utilizing 14 near-infrared emitting diodes with narrow bandpass filters, a silicon detector system, and a fully integrated microprocessor. Simple octane number determination requires three easy steps: sampling a background signal, acquiring two absorption spectra of the gas sample, and then acquiring a second background signal. Analyzer is pre-calibrated for unleaded gasoline and ethanol-blended fuels, and can be calibrated for up to eight additional fuel types. The analyzer is small, lightweight, and operates on "AA" batteries or AC. Before each reading, the unit standardizes itself to assure accuracy. The octane number is printed with time and date on the built-in printer. All data can be downloaded via the RS232 port to an external computer.Calibration Software RS232 CableAluminum Carrying Case Printer Paper Roll Sample Holder Light CoverAA Battery Sample Holder LabelAccuracy and repeatability equivalent to ASTM approved CFR engines test methods (ASTM D2699, D2700)Sample Holder: Sealed, cubical glass container (75mm optical path length)Sample Volume: 8 Ounces (approx. 225 mL)Operating Temperature Range: 7°C - 38°C - Pre-calibrated for unleaded & ethanol-blended gasoline (Analyzer can be calibrated for up to 8 additional fuel types.) Battery operated (6 AA batteries)115V 60Hz220-240V 50/60Hzwxdxh,in.(cm): 13 1⁄2x4 1⁄2x2 1⁄2 (34x11 1⁄2x6 1⁄4) Net Weight: 12 lbs (5.5kg)K88601 Printer Paper, 10 RollsK88603 Sample Holder (additional)K88604 Sample Holder (Box of 12)K88605 Light ShieldK88606 RS232 CableK88607 Aluminum Sample Carrying Case w/12 Sample HoldersK88608 Sample Holder Lids, Quantity 12K88609 Sample Holder Labels, Quantity 12K88610 25 Sample MemoryK88612 Cetane Number CalibrationK88602 Additional Fuel CalibrationK88613 GPS Locator

InfraCal 2 TRANS-SP - Oil In Water/Soil AnalyzerTOG/TPH in water/soil, FOG in wastewaterAlat Laboratorium AirThe InfraCal 2 TRANS-SP  is recommended for measuring oil in water, TPH in soil or FOG in wastewater concentration levels using the traditional EPA methods 413.2 and 418.1 or ASTM method D7066-04and Freon-113, hydrocarbon-free grade of perchloroethylene, AK-225, S-316 or other spectroscopic infrared transparent solvent as the extracting solvent. Since the extract is deposited into a 10 mm quartz cuvette cell with Teflon stopper, light end volatile components are retained for measurement. Accurate down to 0.1 ppm.The InfraCal 2 TRANS-SP, the latest introduction to our easy to use analyzers, uses the same measurement technology as the original InfraCal Model CVH, with added features such as data storage and transfer, multiple calibrations and password protection for instrument settings.Specifications       • MDL Water:  0.1ppm       • MDL Soil:  1ppm       • Solvent(s):  Perchloroethylene, S-316, Freon-113       • Method Compares:  EPA 1664, ISO 9377-2       • Method Complies:  ASTM D7066, EPA 413.2, EPA 418.1HighlightsThe fact that InfraCal Analyzers over 10 years old are still operating in the corrosive environment of an offshore oil rigs attests to their rugged, dependability.   The analysis procedure takes less than 15 minutes and can be done by minimally trained personnel.  They use the field proven infrared technology for measuring oil in water, oil content in drilling mud or drill cuttings, TPH (total petroleum hydrocarbons) in soil and FOG (fats, oil and grease) in wastewater.Operating PrincipleThe InfraCal TOG/TPH Analyzer makes use of the fact that hydrocarbons such as oil and grease can be extracted from water or soil through the use of an appropriate solvent and extraction procedure.  The extracted hydrocarbons absorb infrared energy at a specific wavelength and the amount of energy absorbed is proportional to the concentration of oil and grease in the solvent.  The analyzer can be calibrated to read out directly in the desired units.SpecificationsItemSpecificationsAnalytical Wavelength/Wave Number3.4 µm, 2930 cm-1Power Requirements18 volts DC, 3.3 amps, internal battery pack availablePower SupplyUniversal AC/DC providedWeight5.8 lb. (2.6 kg) with battery -7.0 lbs (3.2 kg)Dimensions(17 cm) x 7.8" (19.8 cm) x 5.2" (13.2 cm)Suggested Operating Range40°F (5°C) – 110°F (40°C)Measurement Range For Water0.1-1000+ ppmFor Soil1-5000+ ppmAnalysis Time10-15 minutes, including extraction processInstrument Repeatability±0.1 ppmCommunication PortUSB, RS 232 InfraCal 2 TRANS-SP (TOG/FOG/TPH) Analyzer   InfraCal 2 TRANS-SPMinimum Detection Limit Water0.1 ppmMinimum Detection Limit Soil1 ppmFor use with Solvent (s):Tetracloroethylene (Perchloroethylene) , S-316, FreonMethod Complies:ASTM D7066, EPA 418.1 & 413.2  405-2035TRANS-SP- Uncalibrated, Internal Battery, Auto Adapter, Set of Four 10mm Quartz Cuvette Cells and Power Supply.405-2035-41TRANS-SP Includes a factory calibration using S-316 standards for samples containing primarily petroleum hydrocarbons with minimal animal/plant oils; Includes Internal Battery, Auto Adapter, Set of Four 10mm Quartz Cuvette Cells, Dust Cover and Universal Power Supply. Includes 1 Calibration Range for Water, Soil Calibration can be added for additional $175 charge: Water: 10, 25, 50, 100, 150, and 200 mg/L *Soil: 100, 250, 500, 1000, 1500, and 2000 mg/kg405-2035-8041TRANS-SP Includes a factory calibration using S-316 standards for samples containing primarily petroleum hydrocarbons with minimal animal/plant oils; Includes Internal Battery, Auto Adapter, Set of Four 10mm Quartz Cuvette Cells, Dust Cover and Universal Power Supply. Includes 2 Calibration Ranges for Water, Soil Calibration can be added for additional $175 charge: Water: 0.5, 1, 2.5, 5.0, and 7.5 mg/L Water: 10, 25, 50, 100, 150, and 200 mg/L *Soil: 100, 250, 500, 1000, 1500, and 2000 mg/kg405-2035-40TRANS-SP Includes a factory calibration using S-316 standards for samples containing primarily animal and/or plant oils; Includes Internal Battery, Auto Adapter, Set of Four 10mm Quartz Cuvette Cells, Dust Cover and Universal Power Supply. Includes 1 Calibration Range for Water: Water: 10, 25, 50, 100, 150, and 200 mg/L405-2035-78TRANS-SP Includes a factory calibration using Tetracloroethylene standards for samples containing primarily petroleum hydrocarbons with minimal animal/plant oils; Includes Internal Battery, Auto Adapter, Set of Four 10mm Quartz Cuvette Cells, Dust Cover and Universal Power Supply. Includes 1 Calibration Range for Water, *Soil Calibration can be added for additional $175charge: Water: 10, 25, 50, 100, 150, and 200 mg/L *Soil: 100, 250, 500, 1000, 1500, and 2000 mg/kg405-2035-7978TRANS-SP Includes a factory calibration using Tetracloroethylene standards for samples containing primarily petroleum hydrocarbons with minimal animal/plant oils; Includes Internal Battery, Auto Adapter, Set of Four 10mm Quartz Cuvette Cells, Dust Cover and Universal Power Supply. Includes 2 Calibration Ranges for Water, *Soil Calibration can be added for additional $175 charge: Water: 0.5, 1, 2.5, 5.0, and 7.5 mg/L Water: 10, 25, 50, 100, 150, and 200 mg/L *Soil: 100, 250, 500, 1000, 1500, and 2000 mg/kg Optional Factory Calibrations:403-1079CLow Range Factory Calibration using Tetrachloroethylene Standard Set (403-1079) Water: 0.5, 1, 2.5, 5.0, and 7.5 mg/L403-1080CLow Range Factory Calibration using S-316 Standard Set (403-1080) Water: 0.5, 1, 2.5, 5.0, and 7.5 mg/L   Calibration Standards Sets403-1080TOG/TPH Low Range S-316 TOG/TPH Five Point Calibration Standard Set Light Mineral Oil in S-316 prepared by a certified laboratory. The set contains 6 standards from 0.5mg/L to 7.5 mg/L (ppm) for water and 5 mg/kg to 75 mg/kg for soil, includes solvent blanks. Recommended for customers in the petroleum industry who are primarily measuring low levels of petroleum hydrocarbons in water or soil.403-1041TOG/TPH High Range S-316 Six Point Calibration Standard Set: Light Mineral Oil in S-316 prepared by a certified laboratory for TOG/TPH Analysis. Nominal concentration values are 100 mg/kg (ppm), 250 mg/kg, 500 mg/kg, 1000 mg/kg, 1500 mg/kg and 2000 mg/kg for soil assuming a 1:1 extraction ratio; and 10 mg/L (ppm), 25 mg/L, 50 mg/L, 100 mg/L, 150 mg/L and 200 mg/L for water assuming a 10:1 extraction ratio. The set contains 6 standards along with a solvent blank in 4 ml flame sealed ampoules. Recommended for customers in the petroleum industry who are primarily measuring petroleum hydrocarbons in water or soil.403-1040FOG/TOG High Range S-316 TOG/FOG Six Point Calibration Standard Set: 50:50 Isooctane/Octanoic Acid in S-316 as per ASTM Method D 7066-04 prepared by a certified laboratory. Nominal concentration values are 10 mg/L (ppm), 25 mg/L, 50 mg/L, 100 mg/L, 150 mg/L and 200 mg/L for water assuming a 10:1 extraction ratio. The set contains 6 standards along with a solvent blank in 4 ml flame sealed ampoules. Recommended for customers measuring nonpolar (petroleum) and polar (animal and vegetable fats) hydrocarbons for TOG or FOG measurements such as municipal wastewater or industrial wastewater that includes animal and vegetable fats.403-1079TOG/TPH Low Range Tetrachloroethylene TOG/TPH Five Point Calibration Standard Set Light Mineral Oil in Tetrachloroethylene prepared by a certified laboratory. The set contains 6 standards from 0.5mg/L to 7.5 mg/L (ppm) for water and 5 mg/kg to 75 mg/kg for soil, includes solvent blanks. Recommended for customers in the petroleum industry who are primarily measuring low levels of petroleum hydrocarbons in water or soil.403-1078TOG/TPH High Range Tetrachloroethylene TOG/TPH Six Point Calibration Standard Set: Light Mineral Oil in Tetrachloroethylene prepared by a certified laboratory for TOG/TPH Analysis. Nominal concentration values are 100 mg/kg (ppm), 250 mg/kg, 500 mg/kg, 1000 mg/kg, 1500 mg/kg and 2000 mg/kg for soil assuming a 1:1 extraction ratio; and 10 mg/L (ppm), 25 mg/L, 50 mg/L, 100 mg/L, 150 mg/L and 200 mg/L for water assuming a 10:1 extraction ratio. The set contains 6 standards along with a solvent blank in 4 ml flame sealed ampoules. Recommended for customers in the petroleum industry who are primarily measuring petroleum hydrocarbons in water or soil.     Accessories403-0012Set of 4 - 10mm Quartz Cuvette Cells403-1013Carrying Case with pre-diced pluck foam. 18.5 x 14.6 x 8"; 10 lbs.403-1086Dust Cover  Field Sampling Kits403-1063Field Sampling Kit for TOG-TPH in Water 100ml Graduated Cylinder  25ml Graduated Cylinder  125 ml Wash Bottle  20ml Beaker  100ul Syringe Disposable Pipettes (100 pc.) Glass Funnel  177ml Graduated Bottles (48 pc)  Septa Caps (48 pc)  Sodium Sulfate, 500g  Silica Gel, 500g  Filter Paper, 100pc 20ml Luer-Lok Syringe & Tip (100pc)403-1010Field Sampling Kit for TOG-TPH in Soil 100ml Graduated Cylinder  25ml Graduated Cylinder  125 ml Wash Bottle  20ml Beaker  100ul Syringe Disposable Pipettes (100 pc.)  Glass Funnel  40ml Vials (72 pc.)  Pocket Balance  Sample Spatula  Silica Gel, 500g  Filter Paper, 100pc  60ml Syringe Cartridge & Plunger (100)  403-1083Field Sampling Kit for Sub-ppm in Water 10ml Glass Luer-Lok Syringe Filters for Glass Luer-Lok Syringe (100 pc This kit is to be used in addition to 403-1063 for sub-ppm in water sampling end

InfraCal 2 ATR-E - Ethanol In Gasoline AnalyzerAlat Laboratorium AirThe InfraCal 2 Ethanol Blend Analyzer for measuring percent ethanol in gasoline is the ideal solution where a quick, accurate, on-site measurement is required and a single, repetitive ethanol blend analysis is needed.  The InfraCal 2 ATR-E is based on proven IR technology, and used by fuel terminals, laboratories and regulatory agencies worldwide.  The compact, easy-to-use InfraCal 2 ATR-E has a measurement range of 0-20 & 70-98%% ethanol in gasoline and an accuracy of +/- 0.2%. These results are comparable to ASTM D4815.  Samples are applied to a  zinc selenide attenuated total reflectance (ATR) sample plate and easily cleaned with a cloth & isopropyl alcohol.  No solvents requiring special ventilation, expensive waste disposal or difficult to clean cells are needed. The analysis can be done by non-technical personnel with no formal training and is ideal for lab or field use. The InfraCal2 ATR-E has a touch screen display, data storage and transfer, a multi-language interface and password protected settings.  The internal battery pack allows for portability and up to 12 hours continuous use, providing results in under a minute at a fuel loading rack, in a laboratory or at a pump in a fueling station.Measurement range: 0 - 20 & 70 - 98% ethanol in gasolineInstrument repeatability: +/- 0.2%Compares to ASTM D4815Highlights  Benefits  FeaturesInternal Data StorageData storage including each measurement tagged with analyst, location and date/time information, and password protected instrument settingsExportDirectly to your PC via USB or a Flash DriveTouch Screen DisplayThe touch screen display allows a simple set up for quick operation along with an easy calibration wizard.Internal BatteryThe internal battery pack allows for portability and up to 6 hours continuous use.Multi-Language InterfaceEnglish, Spanish, French, ArabicPassword Protected SettingsCalibration and data are password protected to avoid accidental deletionNo need for Installation/CommissioningThe InfraCal 2 is a portable analyzer, weighing less than 5 lbs. with a 6 in. square foot print, requiring no installation or commissioning, little to no routine maintenance or recalibration.Minimal ConsumablesThe analysis requires little to no consumables making the cost-per-test minimal.SpecificationsItemSpecificationsAnalytical Wavelength/Wave Number9.6 µm, 1045cm-1Power Requirements18 volts DC, 3.3 amps, internal battery pack Power SupplyUniversal AC/DC providedWeight5.8 lb. (2.6 kg) with battery -7.0 lbs (3.2 kg)Dimensions(17 cm) x 7.8" (19.8 cm) x 5.2" (13.2 cm)Suggested Operating Range5°C - 40°CMeasurement Range0 - 20 & 70 - 98% ethanol in gasolineAnalysis TimeLess than 30 secondsInstrument Repeatability0 - 20%±0.2%, 20 - 98%±1% of ethanol in petrol concentrationCommunication Port USB, RS 232  InfraCal 2 Model ATR-ECompares to:ASTM D4815Measurement range:0 - 100% Ethanol in GasolineIntrument repeatability:+/- 0.2  InfraCal 2 ATR-E, for measuring % Ethanol in Gasoline.405-2042Model ATR-E Uncalibrated Includes Internal Battery, auto adapter and universal power supply.405-2042-30Model ATR-E Calibrated: 0-20% & 70-100% Ethanol in Gasoline using P/N's: 403-1026 or 403-1027 Includes Internal Battery, auto adapter and universal power supply.Accessories 403-0013Carrying Case for InfraCal Analyzers with pre-diced pluck foam. 18.5" x 14.6" x 8"; 10 lbs.403-1086Dust Cover  Calibration Standard Sets 403-10265 Point Ethanol Low Concentration Calibration Standard Set Standard concentrations are 0, 5, 10, 15, and 20% ethanol in gasoline. Standards are prepared by a certified laboratory. Each vial contains 20 ml of standard, good for a minimum of 15 tests.403-10275 Point Ethanol High Concentration Calibration Standard Set Standard concentrations are 70, 80, 90, 95, and 100% ethanol in gasoline. Standards are prepared by a certified laboratory. Each vial contains 20 ml of standard, good for a minimum of 15 tests.

InfraCal 2 ATR-B - Biodiesel In Diesel AnalyzerBiodiesel in dieselAlat Laboratorium AirThe InfraCal 2 Biodiesel Blend Analyzer for measuring percent biodiesel in diesel is the ideal solution where a quick, accurate, on-site measurement is required and a single, repetitive biodiesel blend analysis is needed. The InfraCal 2 ATR-B is based on proven IR technology, originally developed by Wilks, and used by fuel distributors, blenders, producers and regulatory agencies worldwide.  The compact, easy-to-use Biodiesel Blend Analyzer has a measurement range of 0 – 100% biodiesel in diesel. These results are comparable to both ASTM D7371 and EN 14078, laboratory methods that require expensive FTIR Spectrometers. Samples are applied to a zinc selenide attenuated total reflectance (ATR) sample plate for immediate results. The analysis can be done by non-technical personnel with no formal training and is ideal for lab or field use. The InfraCal2 ATR-B has a touch screen display, internal data storage and transfer, a multi-language interface and password protected settings.  The internal battery pack allows for portability and up to 6 hours continuous use, providing results in under a minute at a fuel loading rack, in a laboratory or at a pump in a fueling station.Measurement range: 0 - 100% biodieselInstrument repeatability: 0 – 30% +/- 0.2% ; 30-100% +/-1.0%Compares to ASTM D7371 & EN 14078Highlights  Benefits  FeaturesInternal Data StorageData storage including each measurement tagged with analyst, location and date/time information, and password protected instrument settingsExportDirectly to your PC via USB or a Flash DriveTouch Screen DisplayThe touch screen display allows a simple set up for quick operation along with an easy calibration wizard.Internal BatteryThe internal battery pack allows for portability and up to 6 hours continuous use.Multi-Language InterfaceEnglish, Spanish, French, ArabicPassword Protected SettingsCalibration and data are password protected to avoid accidental deletionNo need for Installation/CommissioningThe InfraCal 2 is a portable analyzer, weighing less than 5 lbs. with a 6 in. square foot print, requiring no installation or commissioning, little to no routine maintenance or recalibration.Minimal ConsumablesThe analysis requires little to no consumables making the cost-per-test minimal.SpecificationsItemSpecificationsAnalytical Wavelength/Wave Number5.7 µm, 1745 cm-1Power Requirements18 volts DC, 3.3 amps, internal battery pack Power SupplyUniversal AC/DC providedWeight5.8 lb. (2.6 kg) with battery -7.0 lbs (3.2 kg)Dimensions(17 cm) x 7.8" (19.8 cm) x 5.2" (13.2 cm)Suggested Operating Range5°C - 40°CMeasurement Range0 - 100% Biodiesel in DieselAnalysis TimeLess than 30 secondsInstrument Repeatability 0 - 30%±0.2%, 20 - 100%±1% of biodiesel (FAME) concentrationCommunication Port USB, RS 232  InfraCal 2 Model ATR-BCompares to:ASTM D7371 & EN 14078Measurement range:0 - 100% biodieselInstrument repeatability+/- 0.2  InfraCal 2 ATR-B Biodiesel Blend Analyzer, for % Biodiesel in Diesel Measurements.405-2041Model ATR-B Uncalibrated: 0 -100% Biodiesel in Diesel. Includes Internal Battery, auto adapter and universal power supply.405-2041-24Model ATR-B Calibrated: 0 -100% Biodiesel in Diesel, using P/N: 403-1024, Includes Internal Battery, auto adapter and universal power supply.Accessories 403-0013Carrying Case for InfraCal Analyzers with pre-diced pluck foam. 18.5" x 14.6" x 8"; 10 lbs.403-1086Dust Cover  Calibration Standard Sets 403-10240-100% Biodiesel in Diesel Calibration Standards The set includes ten standards; 0, 2, 5, 10, 15, 20, 25, 30, 50, 75, 95, 100 biodiesel in High Cetane diesel fuel prepared by a certified laboratory. Each vial contains 20 ml of standard, good for a minimum of 15 tests.

InfraCal 2 ATR-SP - Oil In Water/Soil Analyzer TOG/TPH in water/soil, FOG in wastewaterAlat Laboratorium AirThe InfraCal Model ATR-SP is recommended for measuring oil in water, TPH in soil or FOG in wastewater concentration levels when using hexane, pentane or Vertrel MCA as the extracting solvent. Measurement data obtained with this analyzer will correlate to EPA Method 1664 as both procedures are based on evaporation techniques and measuring the residual oil and grease. The analyzer is equipped with a built-in cubic zirconia horizontal attenuated total reflection (HATR) stainless steel sample stage.   The InfraCal 2 ATR-SP is a direct replacement for the original InfraCal HATR-T2 used worldwide for the determination of TOG/TPH in water and soil.Minimum Detection Limit Water: 0.3 ppmMinimum Detection Limit Soil: 3 ppmMethod Compares: EPA 1164 & ISO 9377-2Solvents: Hexane, pentane, cyclohexane & Vertrel MCAHighlightsAs offshore oil wells age, the increase of produced water challenges wastewater treatment systems.  In order to ensure oil levels in the water are under the regulatory limit, it is important to do regular testing.  Infrared analysis has been used for off-shore oil in water measurements for over 45 years.  Infrared is an accepted oil content measurement as it is least affected by changes in produced water composition.For industrial pretreatment of wastewater and public water treatment plants a simplified procedure for monitoring FOG discharges can avoid fines, sanitary sewer overflows (SSOs) and give on-site results in less than 15 minutes rather than waiting days or weeks for an off-site laboratory result.The InfraCal 2 has added features such as touch screen display, data storage and transfer, a multi-language interface and password protected settings.  The internal battery pack allows for portability and up to 6 hours continuous use.Operating PrincipleThe InfraCal 2 ATR-SP analyzer is designed to measure solvent extractable material (oil and grease) by infrared determination in water or soil using hexane, pentane, cyclohexane or Vertrel MCA for the extraction procedure. A detector with a fixed 3.4 μm (2940 cm-1) filter is used to measure oil and grease concentrations. The ATR-SP correlates with EPA Methods 1664 as well as with the ASTM D7066 Method and EPA 413.1 and 418.1.  The ATR-SP makes use of the fact that oil and grease can be extracted from water or soil through the use of an appropriate solvent and extraction procedure. The extracted hydrocarbons absorb infrared energy at a specific wavelength and the amount of energy absorbed is proportional to the concentration of hydrocarbons in the solvent. The analyzer can be calibrated to read out directly in the desired units such as %, ppm, mg/L or mg/kg.  The touchscreen display includes the capability for multiple calibrations, a wizard guide for calibration, multilevel user database, multiple languages with user preference selection, high/low alarm and control limits, and measurements stored in a history table for recall or export to a flash or serial port.SpecificationsItemSpecificationsAnalytical Wavelength/Wave Number3.4 µm, 2930 cm-1Power Requirements18 volts DC, 3.3 amps, internal battery pack availablePower SupplyUniversal AC/DC providedWeight5.8 lb. (2.6 kg) with battery -7.0 lbs (3.2 kg)Dimensions(17 cm) x 7.8" (19.8 cm) x 5.2" (13.2 cm)Suggested Operating Range5°C - 40°CMeasurement Range For Water0.3-1000+ ppmFor Soil3-5000+ ppmAnalysis Time10-15 minutes, including extraction processInstrument Repeatability±0.2 ppmCommunication PortUSB New High Range Measurement of Oil In Water or SoilThe InfraCal 2 analyzer with an ATR sample stage can now be used for measuring the 0.5-10% range of oil in water or soil. The sample is extracted using a solvent that does not have an infrared absorbance at the hydrocarbon wavelength and, therefore, does not require evaporation. Measuring the extract directly in the solvent, instead of evaporating off the solvent, allows for percent range measurements with the same ATR sample stage used to measure the ppm levels.Measurement Range Water: 0.5 – 10%Measurement Range Soil: 0.5 – 10%Solvents: S-316, Tetrachloroethylene InfraCal 2 ATR-SP (TOG/FOG/TPH) Analyzer  InfraCal 2 Model ATR-SPMinimum Detection Limit Water0.3 ppmMinimum Detection Limit Soil3 ppmFor use with Solvent(s):Hexane, pentane, cyclohexane, Vertrel MCAMethod Compares to:EPA 1664 & ISO 9377-2  405-2034ATR-SP Uncalibrated; Includes Internal Battery, Auto Adapter, 100 U Syringe, Universal Power Supply405-2034-44Includes a factory calibration using Hexane TOG/TPH High Range Calibration Standards for samples containing primarily petroleum hydrocarbons; Includes Internal Battery, Auto Adapter, 100 ul Syringe, Universal Power Supply, Dust Cover Includes 1 Calibration Range for Water, Soil Calibration can be added for additional $175 charge: Water: 10, 25, 50, 100, 150, and 200 mg/L Soil: 100, 250, 500, 1000, 1500, and 2000 mg/kg405-2034-8144Includes a factory calibration using Hexane TOG/TPH Low & High Range Calibration Standards for samples containing primarily petroleum hydrocarbons; Includes Internal Battery, Auto Adapter, 100 ul Syringe, Universal Power Supply, Dust Cover Includes 2 Calibration Ranges for Water, Soil Calibration can be added for additional $175 charge: Water: 0.5, 1, 2.5, 5.0, and 7.5 mg/L Water: 10, 25, 50, 100, 150, and 200 mg/L Soil: 100, 250, 500, 1000, 1500, and 2000 mg/kg405-2034-72Includes a factory calibration using Hexane TOG/FOG Calibration Standards for wastewater that contains animal and/or plant oils; Includes Internal Battery, Auto Adapter, 100 ul Syringe, Universal Power Supply, Dust Cover Includes 1 Calibration Range for Water: Water: 10, 25, 50, 100, 150, and 200mg/LOptional Calibrations: 403-1081CFactory Calibration using Hexane Low Range Calibration Standards (403-1081) Water: 0.5, 1, 2.5, 5.0, and 7.5 mg/L Accessories403-0013Carrying Case for InfraCal Analyzers with pre-diced pluck foam. 18.5" x 14.6" x 8"; 10 lbs.403-1086Dust Cover Calibration Standards Sets403-1081Low Range Hexane TOG/TPH Five Point Calibration Standard Set Light Mineral Oil in hexane prepared by a certified laboratory. The set contains 6 standards from 0.5mg/L to 7.5 mg/L (ppm) for water and 5 mg/kg to 75 mg/kg for soil, includes solvent blanks. Recommended for customers in the petroleum industry who are primarily measuring low levels of petroleum hydrocarbons in water or soil.403-1044Hexane TOG/TPH Six point Calibration Standard Set Light Mineral Oil in N-Hexane prepared by a certified laboratory for TOG/TPH Analysis. Nominal concentration values are 100 mg/kg (ppm), 250 mg/kg, 500 mg/kg, 1000 mg/kg, 1500 mg/kg and 2000 mg/kg for soil assuming a 1:1 extraction ratio; and 10 mg/L (ppm), 25 mg/L, 50 mg/L, 100 mg/L, 150 mg/L and 200 mg/L for water assuming a 10:1 extraction ratio. The set contains 6 standards along with a solvent blank in 2 ml flame sealed ampoules. Recommended for customers in the petroleum industry who are primarily measuring petroleum hydrocarbons in water or soil.403-1072Hexane TOG/FOG Six Point Calibration Standard Set 50:50 Soybean Oil/Hexadecane in N-Hexane prepared by a certified laboratory. Nominal concentration values are 10 mg/L (ppm), 25 mg/L, 50 mg/L,100 mg/L, 150 mg/L and 200 mg/L for water assuming a 10:1 extraction ratio. The set contains 6 standards along with a solvent blank in 2 ml flame sealed ampoules. Recommended for customers measuring non-polar (petroleum) and polar (animal and vegetable fats) hydrocarbons for TOG or FOG measurements such as municipal wastewater or industrial wastewater that includes animal and vegetable fats.   Field Sampling Kits403-1011Field Sampling Kit for TOG-TPH in Water 100ml Graduated Cylinder 25ml Graduated Cylinder 125 ml Wash Bottle  20ml Beaker  100ul Syringe Disposable Pipettes (100 pc.) Glass Funnel  177ml Graduated Bottles (48 pc)  Septa Caps (48 pc)  Sodium Sulfate, 500g  Silica Gel, 500g  Filter Paper, 100pc  403-1010Field Sampling Kit for TOG-TPH in Soil 100ml Graduated Cylinder  25ml Graduated Cylinder  125 ml Wash Bottle  20ml Beaker  100ul Syringe Disposable Pipettes (100 pc.)  Glass Funnel  40ml Vials (72 pc.)  Pocket Balance  Sample Spatula  Silica Gel, 500g  Filter Paper, 100pc  60ml Syringe Cartridge & Plunger (100)  403-1083Field Sampling Kit for Sub-ppm in Water 10ml Glass Luer-Lok Syringe Filters for Glass Luer-Lok Syringe (100 pc This kit is to be used in addition to 403-1063 for sub-ppm in water sampling